They are making several great observations regarding A Step-by-Step Guide to Installing a Bathtub in general in this post down the page.
Mounting a tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually certified yourself for the work as well as are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to think about using one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This post will help you mount a new tub in your shower room if you have already gotten a brand-new tub as well as do not need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the restricted gain access to that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipes have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the tap in position with the maker supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water and inspect all joints and new pipework for leakages and tighten them if needed. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been utilized at the very least once as this will certainly resolve it into its final setting.
Planning for the Installation
First of all, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bath and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealer can break fairly very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about Installing A Bathtub? Make a comment below. We'd be delighted to know your views about this page. Hoping that you visit us again in the near future. In case you enjoyed reading our blog post kindly make sure you remember to pass it around. Thanks a lot for your time invested reading it.
Click Here To Find Out More